Ghost 2 Immobiliser Reviews
The Ghost 2 immobiliser makes use of modern technology to stop car theft. The device is hidden by thieves, and it only starts your engine when a PIN number or app is entered.
It is weatherproof and connects to the CAN data network of your vehicle. It has a service/valet function that allows you to temporarily start your car when it is in garage.
Easy to install
The Ghost immobiliser shields your car from theft of keys or hacking, as well as cloning. It utilizes an PIN code system that is integrated into your vehicle's electronic control unit, making it impossible for thieves to identify. Contrary to traditional immobilisers it does not require any special keys or sensors and is completely hidden from view with no LEDs or signals that signal its presence. It's also less expensive than replacing an ECU or installing a new key fob and can reduce the cost of your monthly insurance.
Follow the instructions of the manufacturer when installing the Ghost 2 vehicle immobiliser. This will ensure that the device functions efficiently and correctly. Test the system following installation by entering the PIN and then starting the vehicle. Regular testing will allow you to spot any issues early.
Make sure you check the position of the CAN H and CAN L wires before beginning the installation. They are vital for powering the immobiliser, therefore it is vital to connect them correctly. Labelling the wires can make it easier to find them when installing. Once you have identified the location of these wires and connected them to a permanent 12V power source and an earthing point. Use a fuse tap to protect the connections from short-circuits or damage.
After connecting the wires, neaten the wires with cable ties to avoid alteration. It is also recommended to cover the wires with insulation tape or heat shrink tubing. This will shield them from electrical shorts, and will increase the life span of the device. Once the wiring is secure, it's a good idea to test the Ghost 2 immobiliser.
The Ghost 2 immobiliser offers a service mode for situations in which you may have to sell your vehicle for example, when it is being repaired or valet-parked. This will disable the PIN sequence for a short period of time. To activate ghost immobiliser tracker , press the brake pedal while pressing the accelerator, and press a number of times that is equal to the first number of the emergency code. The system will then enter service mode. This is confirmed by flashing 5 times the indicator signal.
Change PIN codes easily
It is simple to secure your vehicle from theft by installing the ghost 2 immobiliser. It is hidden within the vehicle, and can only be accessed by a special code. The device communicates with the vehicle ECU through its data bus and does not rely on radio frequency signals, as aftermarket alarm systems or traditional Thatcham immobilisers do. This makes it difficult for thieves to detect the click of an immobiliser relay or add new keys. The control unit is hidden in the vehicle's wiring or dashboard, and isn't physically altered to reset the system.
The ghost 2 immobiliser connects to your vehicle's CAN Data network and makes use of the buttons already present on the steering wheel, door panels and the centre console to create a customisable sequence of up 20 button presses. These must be entered prior to the engine can start - just like the PIN code. This unique system can be reprogrammed and does not require wire cutting during installation. You can also put your vehicle in Valet or Service mode to allow it to start for a short time when you give it to a mechanic to work.
The app can also be used to block your PIN number if you've lost your keys, or change it. This feature is especially helpful in the event that you have offered your vehicle to someone else to use as a valet parking space or for servicing because it prevents them from starting your car and taking it away without your consent. It's also unnoticeable to professional thieves because it does not make use of radio frequencies or circuits.
The ability of the immobiliser protect against relay thefts is another excellent feature. Relay theft is a popular method of car theft, where criminals hack into your car's diagnostic port, then modify the original signal transmitted by the key to the vehicle's ECU to trick it into thinking that the key is valid. This is the way traditional immobilisers are removed, however with a ghost 2 immobiliser, the signal is blocked before it reaches the ECU.
Easy to use app
Ghost 2 is an immobiliser that is revolutionary. It protects your vehicle from key-cloning. It is activated by connecting to the CAN data network in your vehicle and demanding that you enter a pin code before it will start the engine. It also stops thieves from using signal spoofing or device spoofing, which are both common techniques used to steal vehicles.
The system is easy to use and functions as a standard auto alarm. Once you install it, you can generate a unique PIN sequence of up to 20 digits long and must be entered before the vehicle is started. This will stop your vehicle from being taken away, even the case that you lose your keys. You can turn off the system with an app on your smartphone.
The ghost is quiet and does emit radio frequency signals. It is a weatherproof, discrete device that can be installed in any vehicle. It can be easily hidden under the dash, the steering wheel, or door panels. car stolen with ghost immobiliser via the CAN data loop to your ECU and is not affected at all by the diagnostic tools used by thieves to identify security systems. It is also not affected by jamming devices that spoof codes.
It is a covert installation that doesn't require any wire cutting or modifications to the vehicle, and it can be utilized as an anti-theft system for all vehicles. Its technology is proven to be efficient and is in line with TASSA standards. The Ghost is a good choice for classic or sports cars. It can also be used as a way to protect vehicles being rental on apps such as Turo.
The Autowatch Ghost 2 is the next generation of car immobilisers. The system is completely inaccessible to thieves, and prevents them from starting your car without your PIN or until they are authorized by the app. It also doesn't emit any radio frequencies or other signals that can be detected by scanners. Installation is fast and simple. The app is easy to navigate and has a user-friendly interface that makes it easy to install and use. It also has an GPS tracker that can help police find the vehicle and locate it.
Simple to reset
It is possible to safeguard your vehicle from theft using a ghost 2 immobiliser. It integrates into your vehicle's ECU creating a wall that thieves cannot break through without the proper pin. The device is also TASSA-certified that means it's recognized by insurance companies. It's a powerful tool for preventing car theft, and it can save you a lot of money over the long term.
Unlike traditional alarm/immobilisers that require cutting of circuits, the Ghost system is directly connected to the vehicle's CAN network and works using your existing buttons on the dashboard as well as the steering wheel. You can set up an individual PIN sequence, which can be up to 20 presses in length. This PIN is required to be entered before the engine can be started the same way as the credit card PIN. The Ghost system is undetectable to thieves, and there are no indicators that signal its presence and makes it the most reliable aftermarket CAN bus immobiliser available on the market currently.
Another advantage of the Ghost system is that it doesn't make use of radio frequency signals, meaning it isn't detected or scanned by thieves. This prevents key attacks that replicate and relay attacks as well as the common method of hacking into the computer system of a car using its CAN bus by searching for signals. The Ghost system is designed so that it can be hidden within your vehicle. There are no LEDs, or other signals to show its presence.
The system has a Transport Mode that disables the Ghost System. This is beneficial for situations when you require temporarily deactivating Ghost for instance, when you're transporting or maintaining your vehicle. This mode isn't as effective as Service Mode as it doesn't disable the Ghost system when you exceed 31 mph in 15 minutes.
To reset your ghost 2 immobiliser, you will need to have the emergency code, which you can obtain from your installer. It is typically hidden under an area for scratch-offs on the card that was provided when you installed the device. It is recommended to keep the emergency code secure and keep it in a safe place that is secure, such as your wallet at home.